ESPRIT 646 Manuel d'installation Page 12
- Page / 56
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
8 Reference & Installation Manual
2.9.3 N.C. Contacts, Without EOL Resistor, With
Tamper Recognition
If your security installation requires tamper
recognition, all detection devices must use normally
closed contacts. Connect the devices and program
the control panel as shown in Figure 14. This setup
will communicate an open or closed zone to the
control panel, displaying open zones on the keypad.
The control panel will also communicate any
detected tampers (cuts) as per Tamper/Wire Fault
Recognition Options (see section 10.7 on page 38).
2.9.4 N.C. Contacts, With EOL Resistor, With
Tamper and Wire Fault Recognition (UL)
If your security installation requires tamper (cut)
and wire fault (short) recognition, all detection
devices must use normally closed contacts.
Connect the devices and program the control panel
as shown in Figure 15. This setup will communicate
an open or closed zone to the control panel,
displaying open zones on the keypad. The control
panel will also communicate any detected tampers
(cuts) and/or wire faults (short) as per Tamper/Wire
Fault Recognition
Options (see section 10.7 on page 38)
2.10 Advanced Technology Zone (ATZ) Connections
Enabling the ATZ feature (see section 7.2 on page 27) allows you install two detection devices per input terminal, therefore,
doubling zone capacity of the control panel. Advanced Technology Zoning is a software-oriented feature, there is no need for
extra modules, simply install the devices as shown in Figures 17 to 19. The control panel will recognize the installed devices as
shown in Figure 16. The extra zones function exactly like any other zone displaying zone status on the keypad and sending
separate alarm codes for each zone. For more information on programming the options mentioned in the following sections refer
to ZONE DEFINITIONS in section 7 on page 26.
When ATZ is enabled, keypad zones are recognized as zones 13 and 14. This means that the control panel will
not be able to distinguish between zone 13 and keypad zone 1 and between zone 14 and keypad zone 2.
Figure 14
Figure 15
Figure 16
- 748+ 24-Zone Control Panel 1
- Table of Contents 3
- Part 1: Introduction 5
- 1.4 Accessories & Keypads 6
- 1.5 About Paradox 6
- Part 2: INSTALLATION 7
- 2.5 Bell/Siren Output 8
- 2.8 Keypad Zone Connections 9
- Disabling 642 Keypad Zones: 10
- Esprit 748+ 7 11
- Tamper Recognition 12
- 2.11 Fire Circuit 14
- 2.12 Serial Output Connector 14
- Part 3: ACCESS CODES 15
- Part 4: PROGRAMMING METHODS 16
- 4.2.3 Decimal Programming 17
- Esprit 748+ 13 17
- 4.2.5 Key Access Programming 18
- 5.1 Panel Answer Options 19
- 5.2 Panel Identifier 19
- Esprit 748+ 17 21
- Part 6: Event Reporting 22
- 6.1 Reporting Options 23
- 6.4 System Account Codes 25
- 6.5 Communicator Formats 25
- 6.6 Reporting Event Codes 26
- 6.7 Auto Test Report 28
- 6.8 Manual Test Report 28
- 6.10 Recent Close Delay 28
- Esprit 748+ 25 29
- Part 7: ZONE DEFINITIONS 30
- 7.1 Zone Speed 31
- 7.3 Intellizones 31
- 7.4 Silent Zones 31
- 7.5 24 Hour & Fire Zones 31
- 7.6 Instant Zones 32
- 7.7 Follow Zones 32
- 7.8 Entry Delay 1 32
- 7.9 Entry Delay 2 32
- 7.10 Partitioning 33
- 7.11 Bypass Enabled Zones 33
- Esprit 748+ 31 35
- 8.1 Timed Auto Arming 36
- 8.2 No Movement Auto Arming 36
- 8.3 One-Key Regular Arming 36
- 8.5 Arming using a keyswitch 37
- 8.6 Bell Squawk 37
- 8.7 Exit Delay 37
- 8.8 Beep on Exit Delay 37
- 8.9 Alarm Transmission Delay 38
- 8.11 Bell Cut-Off Time 38
- 8.12 Code Priority 38
- 9.1 PGM Types 39
- 9.2 PGM Timer Setting 39
- 9.3 PGM Options 40
- Part 10: OTHER OPTIONS 41
- 10.5 Panel Time 42
- 10.6 Time Correction 42
- 10.8 Tamper Bypass Options 43
- 10.9 Installer Test Mode 43
- 10.11 Audible Trouble Warning 43
- 10.12 Power Down Reset 43
- 474747 44
- 11.4 Stay Arming 45
- 11.6 System Disarming 46
- 11.7 Alarm Memory 46
- 11.9 Manual Zone Bypassing 46
- 11.10 Bypass Recall 47
- 11.11 Keypad Chime Zones 47
- 11.13 Key Access Programming 48
- Warnings 49
- Esprit 748+ 47 51
- Esprit 748+ 49 53
Produits connexes et manuels pour Claviers numériques ESPRIT 646
(28 pages)
(36 pages)
(26 pages)Breville HB95 manuály
Uživatelské manuály a uživatelské příručky pro Malé kuchyňské spotřebiče Breville HB95.
Poskytujeme 1 manuály pdf Breville HB95 ke stažení zdarma podle typů dokumentů: Manuál s instrukcemi
Commentaires sur ces manuels